When you’re looking over different welding helmet options, you might come across the phrase “ANSI Approved.” ANSI is the regulating body that makes standards governing the performance of welding helmet shades, among many other things. The most recent standard comes from 2003 and is called ANSI Z87.1-2003. It specifies various tests a shade needs to pass to be certified. The key here is that many welding helmets were formerly ANSI-approved, but that was before the increased standards that came about in 2003. Make sure any helmet you choose meets the more modern version of helmet standards. There are a lot of basic welding masks on the market. These are simple frame-mounted masks that tilt up and down, have the most basic level of fixed-darkness shading, and have basically no additional protection for things like your neck, ears, or top of your head. Find even more information on Welding Equipment.

Implementing physical barriers and clear signage around welding areas helps to alert other workers and visitors to the potential dangers and restricts access to authorized personnel only. Barriers and signs serve as preventive measures to protect non-welders from accidental exposure to sparks, UV radiation, and other hazards associated with active welding sites. Beyond preventive safety measures, welders and all workshop personnel should be trained in emergency response protocols. This includes knowing how to handle welding accidents, such as burns or exposures to toxic fumes. Effective emergency response training ensures that all employees are prepared to act quickly and efficiently in case of an accident, which can minimize injuries and potentially save lives.

The strength of a joint can be imperative or a non-factor, depending on the purpose of the welding process. Arc welding joints are generally extremely strong unless they are not performed properly. The resulting strength of the material is often at least as strong as the base materials and, in many cases, actually stronger. Brazing joints are not structural in general, but they can bear some load. In plumbing, for example, water hammering can be an issue in some systems, so the joints need to be able to stand up to that kind of force. They are not structural, however, so there is a maximum load they can bear. Soldering joints are almost never structural in any way, and the forces they handle are more electrical than tensile, linear, or shear. As such, they are not very strong, but they don’t need to be. There should, ideally, be next to no force put on them.

Friction welding is a solid-state process that uses, as the name suggests, friction to fuse metals together. Unlike most welding processes, it doesn’t use a welding torch, welding rods or a shielding gas to create welds. The process only uses the heat generated from high rotational, vibrational or lateral contact speeds between two clean metals to create a bond. The metal residue formed during this procedure is removed after the cooling process. The welding equipment used in friction welding is more eco-friendly than other methods as it doesn’t emit harmful welding fumes or release toxins into the atmosphere. Its simplicity makes it a great option for welding drill bits, connection rods, axle tubes and valves.

How to pick a welder tips: Duty cycle: The advertised amperage of the machine offers a headline guide, but the duty cycle of the machine gives up the truth. Light industrial machine duty cycles can be as low as 20%, but more heavy duty MIG’s should range between 40-60%. If a 300amp MIG has 30% duty cycle for instance, it’s on the edge of acceptability. Duty cycle is determined by how many minutes out of 10, it can weld at 100%. Duty cycle testing: MIGS tested at 20 Degrees & 40 Degrees we consider good. (Beware any manufacturer who doesn’t quote an ambient temperature for testing) Manufacturer’s warranty: Always a great guide to quality. A three year warranty is good. Weld characteristics: Make sure the arc is smooth & suits your application. (Some machines are better suited at the low range and others at higher amperage range).

The sort of build quality that you’d expect from Makita. This angle grinder is tough, well put together and built to take a beating. Makita have included a lock-off power switch. I’m a big fan of these compared to the “deadman” style switch you need to hold to keep the disc spinning. They can tire your hand out quickly and aren’t ideal for long grinding sessions. You get a 2.5m power cable to play with. It’s long enough for most grinding jobs, and the quality of the power cord is excellent as well. Makita use labyrinth rings to seal the bearings against dust. Anyone who uses angle grinders a lot know how much dust they produce, so this is a welcome feature. Attaching the side handle can be a bit of a pain. You’ll need a long screwdriver to hold the bolt in place inside the handle. Compared to simple screw-in handle on the Bosch GWS 7-115, this one can be tricky.

United Kingdom market choice: Miller is a Wisconsin-based company that has been in the business since 1929. At just 38 pounds, the Millermatic is ultra-portable and is one of the lightest welders on our list. It is preferred by amateur welders and professionals alike for its usability. It is also one of the most expensive at over $3300, so bear that in mind as you read on! The Millermatic runs at dual voltage. It welds stainless steel, mild steel, and aluminum (with the help of a spool gun). It can weld mild steel to a thickness of 3/8 inches, giving it greater ability than the Hobart Handler. As for its aluminum welding capabilities, it can weld from 18 gauge to 3/8 inches again. It comes with flux core abilities.

The following tips may help: Use the right type of regulator for the gas cylinder. Take care to inspect the regulator before attaching to the cylinder. If the connections aren’t properly made, perhaps you might be using the wrong device. Thus, it is wise to replace it with the right one. Close the valve of the cylinder, as well as release the pressure from the regulator, before removing it from a cylinder. Remove the regulator from the cylinder while transporting it to another location.

Many companies get completely “bogged down” in the paperwork required to run a business. But with today’s latest technological advances, there are items that can be a great help. For instance, Lincoln Electric offers something called ArcWorks software which can document procedures, create drawings everyone in the shop can access, keep track of welding operator’s qualifications, and many other things. Software such as this can be tailored to the individual company’s needs and provide great efficiencies and also eliminate mistakes. Adding Robotics or Hard Automation to the Operation: Today’s technological advances offer many options. Robotics can be justified when the volume of parts a company produces is so great that it can offset the monies spent on a robot. Robotics can also be considered if there are a number of different parts that are similar enough in nature to be able to be handled by the same robot. If robots are not justified, a company might determine that fixturing or hard automation could be used to increase efficiency or quality. One company incorporated fixturing and clamps to hold down a tank while the seam was being welded. In another case, an automotive manufacturer decided that automation was necessary because of the amount of parts and intricate angles and welding positions.

The Everlast Powermig 200 welder offers dual voltage inputs and weighs only 35 pounds due to inverter technology. It’s not only MIG-capable, you can also use it for flux core welding or as a stick welder. When your machine can stick weld and connect gas at the same time, all you need to buy is a connector block and you gain TIG ability too, although Everlast doesn’t say so. The Powermig 200 features a burn back control, automatically adjusting the wire length at restart. 200 amps can weld ?-inch steel in a single pass. Dual digital displays and a low-spatter arc control system are nice features in this price range. Preflow and Postflow improves weld quality, reducing porosity by starting the gas shield before the arc begins and cutting the gas off after the arc stops. The burn back control feature resets the length of the wire feed before you strike another arc. Another nice feature is the digital controls that give you a nice reading of exactly what your voltage and wire speed is. Everlast includes a gas regulator with this rig and backs it with a 3-year warranty. With stick capability and the ability to use it on either household or industrial power, this is quite a bit of welder for the money.

Some advices on welding equipment, MIG and TIG welders, plasma cutters. TIG Welding / Gas Tungsten Arc Welding (GTAW) — TIG welding is an arc welding process that uses a non-consumable tungsten electrode to produce the weld. The weld area is protected from atmospheric contamination by a shielding gas (usually argon) and a filler metal, though some welds, known as autogenous welds, do not require it. A constant-current welding power supply produces energy that is conducted across the arc through a column of highly ionized gas and metal vapors known as plasma. TIG welding is most commonly used to weld thin sections of alloy steel, stainless steel and nonferrous metals such as aluminum, magnesium and copper alloys. The process grants the operator greater control over the weld than other welding processes, allowing for strong, high-quality welds. TIG welding is comparatively more complex and difficult to master than other processes and is significantly slower.

This portable weld fume extractor weighs 50 pounds only and features a 16-foot flexible wire. I’ve found the wheels to be extremely useful to move it around anywhere I need. It’s perfect for people who want something efficient but highly portable as well. The S130/G130 is an excellent option for manual welding around the house and store. Adaptable and Durable. The S130/G130 is a highly adaptable and powerful welding fumes extraction system in a small size. This unit can be used at welding school training due to its compact build quality and efficient fume extraction system. The 16-inch hose that it comes with is enough to cover any small to medium area. The machine is made with high-quality steel that makes it sturdy and durable.

This drill has a powerful 9 Amp motor, high-end 2-coil magnet, and compatible with ¾” diameter shank annular cutters. To start off, this drill is very proud of how easy it is to handle. It weighs a mere 26.5 pounds and it has a conveniently located handle, making uncomfortable drilling positions more bearable. It has a straightforward 2-button control panel that is also conveniently located and easy to use. Other perks that you get with this drill is a hard case and, depending on where you buy, you may also receive a kit containing German-made annular cutters. Like some of the other drills in this list, you can also fit the feeding handles on either side of the drill, depending on what is ergonomic and comfortable for you. This drill also has an easy to turn off feature to add an element of safety to your drilling. This button is big and easily accessible. This is a solid drill that is perfect for all handymen.

The story of ESAB is the story of welding. When our founder Oscar Kjellberg developed the world’s first coated welding electrode in 1904, he launched a company whose innovation and uncompromising standards have helped create the history of welding itself. For more than 100 years, ESAB has been powered by the will to continuously seek new and improved ways of serving our customers. This has made ESAB a world leader in welding products and advanced cutting systems. In 2012, ESAB was acquired by Colfax Corporation, one of the world’s leading diversified industrial manufacturing companies. Colfax, like ESAB, is a solidly customer-focused company that places strong emphasis on constant innovation and improvement. From the firsts by our founder to our global growth, we take pride in what we’ve accomplished in more than a century. But we do so with a keen eye on the future. What can we do better? It’s only when we seek to build upon all we’ve learned, to perfect the innovations our customers count on to work confidently, and push ourselves and our company further that we can boldly face the future. This is how we continue to write the history of welding and cutting. At the end of the day, it’s not where you’ve been that matters most – it’s where you’re going. And for us, that’s forward.

Welding Supplies Direct are the UK distributor for GPPH welding tables, manufactured to the highest standards in Europe. GPPH’s range of welding benches and tables are laser cut for precision and are used in every branch of industry. These welding tables offer perfect flatness (+/- 0.5MM) & are made from 15MM thick S355J2+N grade steel. Our modular welding benches come equipped with a hole system of all sides (tabletop & all sides); the holes are 28MM in diameter and have a chamfered edge for easy tool assembly. You have the option of standard legs or castors being fitted, too.

The Lincoln PowerMIG 210 is the ultimate MIG welder for versatility. It comes with the capability to perform MIG, Stick, TIG and Flux Core welding at both 120v and 240v. This is perfect if you’re looking to buy a MIG welder and are considering buying a TIG or Stick welder as well. Buying a multi-process welder like the PowerMIG 210 can save you a lot of money rather than buying separate machines. Lincoln are the market leaders when it comes to manufacturing quality and the PowerMIG 210 is top of the range to build quality and weld quality. The digital display on the front of the machine lets you easily key in your variables to get you get set up in no time at all with an easy to use user interface. See the full review here.

For some people, the best MIG welder is one that they can take with them wherever their jobs might take them. Welding is one of the most in-demand talents in the UK at the moment, with plenty of manufacturers and mechanics on the hunt for flexible experts who can deliver state-of-the-art welds in a hurry. This MIG Welder portable inverter system comes with everything you need to take your talent with you on-the-go. The system is neatly contained within a compact and light-weight blue package, where you’ll find everything you need for a car welder or home welder, including an optional spool gun for aluminium welding, a 3M MIG torch, earth clamp and lead, and gas hose & regulator. There’s also an easy-to-follow manual included, and a 3-year warranty if you’re concerned about getting the most out of your investment. Overall, this welding machine, created by R-Tech is perfect for people who want to get the most out of a smooth and efficient MIG welding experience. It offers an all-in-one kit for professionals and beginners alike, although it seems to be designed more for the everyday welder than the hobbyist. See additional details on https://www.weldingsuppliesdirect.co.uk/.

Sealey is one of the biggest manufacturers of tools and accessories in the UK, offering approximately 8000 items including tools for home, repair shops, agricultural facilities, as well as cleaning. In this variety, we found a gasless MIG welder MIGHTYMIG 100. The machine is able to weld metal sheets of a different thickness thanks to a toggle that allows setting the amperage to the minimum and maximum. The output range will be 55? and 100?, respectively. We should say that the welding time at the minimum power won’t be over 6 minutes. Yet, this welder will run for about 2 minutes at 90? and that’s great considering its moderate price. In addition, you’ll be able to manage the joint by varying the speed of the wire feed, just turn the relevant control knob to the desired setting. By the way, the welder is compatible with a flux-cored wire up to 0.9 mm, and the weight of the spool should be 0.9 kg. Like most welding tools, it features an overheating protection, and the orange light will notify you when the welder gets overheated after a long use. Apart from that, the forced air cooling system will chill the welder’s internal parts. The welder has a non-live torch for your convenience that will increase the accuracy of welding and provide safety.